This commit adds "deno add" subcommand that has a basic support for
adding "jsr:" packages to "deno.json" file.
This currently doesn't support "npm:" specifiers and specifying version
constraints.
Some `deno_std` tests were failing to print output that was resolved
after the last test finished. In addition, output printed before tests
began would sometimes appear above the "running X tests ..." line, and
sometimes below it depending on timing.
We now guarantee that all output is flushed before and after tests run,
making the output consistent.
Pre-test and post-test output are captured in `------ pre-test output
------` and `------ post-test output ------` blocks to differentiate
them from the regular output blocks.
Here's an example of a test (that is much noisier than normal, but an
example of what the output will look like):
```
Check ./load_unload.ts
------- pre-test output -------
load
----- output end -----
running 1 test from ./load_unload.ts
test ...
------- output -------
test
----- output end -----
test ... ok ([WILDCARD])
------- post-test output -------
unload
----- output end -----
```
As we add tracing to more types of runtime activity, `--trace-ops` is
less useful of a name. `--trace-leaks` better reflects that this feature
traces both ops and timers, and will eventually trace resource opening
as well.
This keeps `--trace-ops` as an alias for `--trace-leaks`, but prints a
warning to the console suggesting migration to `--trace-leaks`.
One test continues to use `--trace-ops` to test the deprecation warning.
---------
Signed-off-by: Matt Mastracci <matthew@mastracci.com>
- Removes the origin call, since all origins are the same for an isolate
(ie: the main module)
- Collects the `TestDescription`s and sends them all at the same time
inside of an Arc, allowing us to (later on) re-use these instead of
cloning.
Needs a follow-up pass to remove all the cloning, but that's a thread
that is pretty long to pull
---------
Signed-off-by: Matt Mastracci <matthew@mastracci.com>
Gets us closer to solving #20707.
Rewrites the `TestEventSender`:
- Allow for explicit creation of multiple streams. This will allow for
one-std{out,err}-per-worker
- All test events are received along with a worker ID, allowing for
eventual, proper parallel threading of test events.
In theory this should open up proper interleaving of test output,
however that is left for a future PR.
I had some plans for a better performing synchronization primitive, but
the inter-thread communication is tricky. This does, however, speed up
the processing of large numbers of tests 15-25% (possibly even more on
100,000+).
Before
```
ok | 1000 passed | 0 failed (32ms)
ok | 10000 passed | 0 failed (276ms)
```
After
```
ok | 1000 passed | 0 failed (25ms)
ok | 10000 passed | 0 failed (230ms)
```
1. Renames zap/fast-check to instead be a `no-slow-types` lint rule.
1. This lint rule is automatically run when doing `deno lint` for
packages (deno.json files with a name, version, and exports field)
1. This lint rules still occurs on publish. It can be skipped by running
with `--no-slow-types`
This changes the lockfile to not store JSR specifiers in the "remote"
section. Instead a single JSR integrity is stored per package in the
lockfile, which is a hash of the version's `x.x.x_meta.json` file, which
contains hashes for every file in the package. The hashes in this file
are then compared against when loading.
Additionally, when using `{ "vendor": true }` in a deno.json, the files
can be modified without causing lockfile errors—the checksum is only
checked when copying into the vendor folder and not afterwards
(eventually we should add this behaviour for non-jsr specifiers as
well). As part of this change, the `vendor` folder creation is not
always automatic in the LSP and running an explicit cache command is
necessary. The code required to track checksums in the LSP would have
been too complex for this PR, so that all goes through deno_graph now.
The vendoring is still automatic when running from the CLI.
This implementation heavily depends on there being a lockfile, meaning
JSR specifiers will always diagnose as uncached unless it's there. In
practice this affects cases where a `deno.json` isn't being used. Our
NPM specifier support isn't subject to this.
The reason for this is that the version constraint solving code is
currently buried in `deno_graph` and not usable from the LSP, so the
only way to reuse that logic is the solved-version map in the lockfile's
`packages.specifiers`.
Step 1 of the Rustification of sanitizers, which unblocks the faster
timers.
This replaces the resource sanitizer with a Rust one, using the new APIs
in deno_core.
This commit removes conditional type-checking of unstable APIs.
Before this commit `deno check` (or any other type-checking command and
the LSP) would error out if there was an unstable API in the code, but not
`--unstable` flag provided.
This situation hinders DX and makes it harder to configure Deno. Failing
during runtime unless `--unstable` flag is provided is enough in this case.
Ensures the Deno process is brought down even when the runtime gets hung
up on something.
Marvin found that the lsp was running without a parent vscode around so
this is maybe/probably related.
We were calling `expand_glob` on our excludes, which is very expensive
and unnecessary because we can pattern match while traversing instead.
1. Doesn't expand "exclude" globs. Instead pattern matches while walking
the directory.
2. Splits up the "include" into base paths and applicable file patterns.
This causes less pattern matching to occur because we're only pattern
matching on patterns that might match and not ones in completely
unrelated directories.
This commit adds a way to connect to the TS compiler host that is run
as part of the "deno lsp" subcommand. This can be done by specifying
"DENO_LSP_INSPECTOR" variable.
---------
Co-authored-by: Nayeem Rahman <nayeemrmn99@gmail.com>
Adds performance measurements for all ops used by the LSP. Also changes
output of "Language server status" page to include more precise
information.
Current suspicion is that computing "script version" takes a long time
for some users.
